Sri Plastic Enterprises ( A Unit of Sri Electronics and Embedded Solutions )

Wireless (RF-BASED)Automatic Water Level Controller
 
    Product Descriptions :

433 MHZ RF Transmitter & Receiver, 90 meter range.

it also work if there is obstacle between the transmitter and receiver.

High quality ABS plastic Enclosure.

Working : This model automatically switches ON and OFF Motor.

When the water level of the overhead tank becomes low means water gets down from the middle sensor and water is present in the underground tank or sump, the motor gets started automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off.

AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.

This model has dry run protection so it only starts the motor if water is present in the underground tank or sump.

Suitable for 0.1 HP to 5.0 HP Motor, Protect motor from dry running.

Motor ON OFF LED indication provided.

Water Level indication provided for both tanks.

Auto and manual mode indication provided 

Supply voltage : 220-270 V AC,

Relay : 40 A

Sensing element : S.S sensor

Auto and Manual mode switch available. In auto mode the motor starts and stops automatically. In manual mode the user can start and stop the motor by pressing the start and stop button of the controller. No additional wiring is required to operate the motor manually. 

Also Suitable for MCB Starter panel and submersible motor, see diagram above for connection.

High quality ABS enclosure provided.

Fully automatic, controls from underground tank to overhead tank so no man power required. Long service Life.

All signals passes in sensors through the AC filter circuit that improve life of sensor,

Isolated supply provided

Sensor fault detection provided, if sensor got failed LED start blinking

Electrolysis free design 

Additional Information:

• Item Code: SEES-1282
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1265
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES Automatic Water Level Controller-NEW MODEL- BORE-Single phase

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

Bore well submersible pumps.
Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

AUTOMATIC WATER LEVEL CONTROLLER(BOREWELL)

•When overhead tank goes 20% pump starts automatically and tank full automatic pump will turn off.
•User can connect with their DOL starter.
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•2 relay based ON and OFF
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :2 Channel SENSOR PINS:
•Common (com), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS

• Brand SEES
• Model Name/Number SEES- BORE
• Operation Type Fully Automatic Tank Type Overhead Tank Phase 1-Phase
• Mounting Type  : Wall
• Type Manual, Automatic, Digital
• Range 3-5m, 5-8m, 11-15m, 8-11m
• Feature Low Temperature Resistant, Monitoring, Conductor, Corrosion Resistant
• Input Voltage 230 V
• Frequency 50 Hz
• Warranty- 1 year

Additional Information:

• Item Code: SEES-1268
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Automatic Water Level Controller-Economic Model- Sump-Single phase can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1267
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

AUTOMATIC WATER LEVEL CONTROLLER(SUMP)
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1266
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

SEES Automatic Water Level Controller-BORE -Single phase

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

Bore well submersible pumps.
Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

AUTOMATIC WATER LEVEL CONTROLLER(BOREWELL)

•When overhead tank goes 20% pump starts automatically and tank full automatic pump will turn off.
•User can connect with their DOL starter.
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•2 relay based ON and OFF
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :2 Channel SENSOR PINS:
•Common (com), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS

• Brand SEES
• Model Name/Number SEES- BORE
• Operation Type Fully Automatic Tank Type Overhead Tank Phase 1-Phase
• Mounting Type  : Wall
• Type Manual, Automatic, Digital
• Range 3-5m, 5-8m, 11-15m, 8-11m
• Feature Low Temperature Resistant, Monitoring, Conductor, Corrosion Resistant
• Input Voltage 230 V
• Frequency 50 Hz
• Warranty- 1 year

Additional Information:

• Item Code: SEES-1269
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Automatic Water Level Controller-Dual Tank  Model- Sump-Single phasecan be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

mono block pump (sump motor)
sump submersible pumps.
Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

SEES Automatic Water Level Controller-Dual Tank  Model- Sump-Single phase : 
•When overhead tank goes 20% pump starts automatically and when tank full automatic pump will turn off
•If sump tank also empty pump will turn off
•Dry run also available, if checks a water flow for one minute if water not flowing more than a minute pump will goes off.
•Water does not waste, and we can save electricity, and our precious time.
•SS contact sensor type.
•Microcontroller based controlling Applications: Home, School, Hospital, Industries, College.

SPECIFICATION POWER INPUT :
•230v input
•12v-1A Transformer
•When the power on red led will glow RELAY :
•12v T relay: 250v 30A, 24v 30A
•Relay used :1 Channel SENSOR PINS:
•Common (com), Sump Low(SL), Sump High (SH), Tank Low (TL), Tank High (TH), Dry run (DR). SENSOR TYPE:
•SS Contact type

• Model Name/Number SEES-SUMP
• Operation Type Fully Automatic Phase 1-Phase
• Range 3.1-5m, 0-3m
• Features Corrosion Resistant, Low Temperature Resistant
• Usage/Application Water Level Controller
• Input Voltage 160V - 250V
• Size 170mm x150mm x 60mm
• Warranty 1 Year
• Dry run trip delay 90 seconds.
• Power onDelay 30 seconds
• Frequency 50 Hz

Additional Information:

• Item Code: SEES-1271
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Benefits :

• No Tension of Water Overflow.
• No Power Wastage, No Water Wastage.
• Overhead Tank always remains Water.
• 4 Level Water Indicators – 25%, 50%, 75% 100% of Water Tank Levels.

Additional Information:

• Item Code: SEES-5026
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

Additional Information:

• Item Code: SEES-1270
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

•  mono block pump (sump motor)
•  sump submersible pumps.
•  Jet Pumps, etc...

This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

Additional Information:

• Item Code: SEES-5025
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

BOREWELL TO OVERHEAD TANK (SEES-BORE)

Automatic Water Level Controller For Single Phase Submersible (bore well) Pumps Panel Driver (Single phase tothree phase). This is a unique device for submersible Pump Up to 2.5 HP Capacity. Our submersible panel drive is the most suitable device for start/Run capacitors Panel Driven Water Pumps. It increases the life of motor to work for year. Application Like Residential Buildings, apartment’s, Commercial Complexes, Industrial Buildings, Hotels, Hospitals, . . . .Etc.

Visual Indications :

Four stage water level indicator for over head tank, water flow indication(Running Line), voltage level indication, power on indication and auto/manual indication.

Features: Switch on the panel if water tank is in required mode and switch off the panel at tank full.

Dry Run
Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off
automatically and gives fault indication.

Voltage Cut-off
Automatic Water Level Controller SEES-BORE automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Surge protection
Built in surge protection is the Main features of SEES series.

Toggle Bypass Switch.
The optional toggle switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

Power ON/OFF Switch.
Small rocker switch to select Power On/Off operation.

Application:
The product is suitable for almost all site conditions water tank for maintaining level
automatically, can be used to control water inflow or outflow, by means of direct pump control or acting as a control switch of a magnetic or combination starter.

Sutable for

 Bore well submersible pumps.
 Jet Pumps,
In SEES series variants are available for any type of pump, bore well and any combination of tanks.

Additional Information:

• Item Code: SEES-5021
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

 mono block pump (sump motor)
 sump submersible pumps.
 Jet Pumps, etc...
This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

Additional Information:

• Item Code: SEES-5020
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

FEATURES

High reliability and Low maintenance. Automatic SEES Water Level Controller SEES-Sump can be used for a long time, no maintenance or repairing would be Required during its operational period. Low AC Voltage sensing circuit to avoid polarization of electrodes in water. These special stainless steel plastic SEES molded conductive electrodes are Long life sensors and do not require frequent cleaning or replacement. Overflow prevention system provides effective and reliable Water level monitoring, with Level Indicators.

Rocker Bypass Switch.

The optional rocker switch is provided to bypass system operation in case of system failure. so no need to disconnect the system when it gets failed.

DryRun

Due to faulty foot valve or air leakage in the pipe if the motor runs dry then it gets switched off automatically and gives fault indication. For more details please watch video demo.

VoltageCut-off

Automatic Water Level Controller SEES-S automatically switches-off the pump if the supply voltage drops below 160V or Crosses 250V.

Sutable for

 mono block pump (sump motor)
 sump submersible pumps.
 Jet Pumps, etc...
This Water level controllers Indicator is highly recommended for metro cities or areas where drinking water is supplied through pipelines which are further distributed in homes, hotels, societies etc.

At large our systems not only help you but your neighbours and society, also as it reduces the wastage of water by cutting down any further overflow than what you need.

Additional Information:

• Item Code: SEES-5024
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES

• Automatic Water Level Controller -Sump/ Bore-3 Phase system
• The underground tank or sump, motor get start automatically. The tank starts filling up. when the water level reaches to the higher level, the motor automatically gets switched off.
• AUTO OFF WHEN TANK IS FULL OR SUMP IS EMPTY.
• This model have dry run protection so it only start motor if water present in underground tank or sump.
• Suitable to any HP Motor as no load comes on our controller. Load passes to existing starter.
• Motor ON OFF LED indication provided.
• Water Level indication provided for both tank and sump.
• Supply voltage : 415 V AC,

• Sensing element : ss  contact type sensor, it is free from oxidation, long life. Any conducting wire can be use for sensor.

  Auto and Manual mode switch available. In auto mode motor start and stop automatically. 

  High quality M.S. enclosure provided.

  Fully automatic, controls from underground tank to overhead tank so no man power required. Long service Life.

• In manual mode user can start and stop motor by pressing start and stop button of controller. 

• No additional wiring require to operate motor manually.

Additional Information:

• Item Code: SEES-5023
• Production Capacity: 1000 NOS
• Delivery Time: 1-2 DAYS
• Packaging Details: CARTOON BOXES